MCP9808T-E/MS【PDF 18/52 页】IC TEMP SENSOR DGTL I2C 8MSOP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录44

14页 15页 16页 17页 [18页]19页 20页 21页 22页

MCP9808

DS25095A-page 18

?2011 Microchip Technology Inc.

5.1.1

SENSOR CONFIGURATION

The MCP9808 has a 16-bit Configuration register

(CONFIG) that allows the user to set various functions for

a robust temperature monitoring system. Bits 10 through

0 are used to select the temperature alert output

hysteresis, device shutdown or Low-Power mode,

temperature boundary and critical temperature lock, and

temperature Alert output enable/disable. In addition, Alert

output condition (output set for T

UPPER

and T

LOWER

temperature boundary or T

CRIT

only), Alert output status

and Alert output polarity and mode (Comparator Output

or Interrupt Output mode) are user-configurable.

The temperature hysteresis bits 10 and 9 can be used

to prevent output chatter when the ambient

temperature gradually changes beyond the

user-specified

temperature

boundary

(see

Section 5.2.2 Temperature Hysteresis (T

HYST

The Continuous Conversion or Shutdown mode is

selected using bit 8. In Shutdown mode, the band gap

temperature sensor circuit stops converting

temperature and the Ambient Temperature register

) holds the previous temperature data (see

Section 5.2.1 Shutdown Mode). Bits 7 and 6 are

used to lock the user-specified boundaries T

UPPER

LOWER

and T

CRIT

to prevent an accidental rewrite.

The Lock bits are cleared by resetting the power. Bits 5

through 0 are used to configure the temperature Alert

output pin. All functions are described in Register 5-2

(see Section 5.2.3 Alert Output Configuration).

CONFIG: CONFIGURATION REGISTER (?/SPAN> ADDRESS 0000 0001b)

U-0

R/W-0

HYST

SHDN

bit 15

bit 8

R/W-0

R-0

R/W-0

Crit. Lock

Win. Lock

Int. Clear

Alert Stat.

Alert Cnt.

Alert Sel.

Alert Pol.

Alert Mod.

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as 0

-n = Value at POR

1 = Bit is set

0 = Bit is cleared

x = Bit is unknown

bit 15-11

Unimplemented: Read as 0

bit 10-9

HYST

: T

UPPER

and T

LOWER

Limit Hysteresis bits

00 = 0癈 (power-up default)

01 = +1.5癈

10 = +3.0癈

11 = +6.0癈

(Refer to Section 5.2.3 Alert Output Configuration.)

This bit can not be altered when either of the Lock bits are set (bit 6 and bit 7).

This bit can be programmed in Shutdown mode.

bit 8

SHDN: Shutdown Mode bit

0 = Continuous conversion (power-up default)

1 = Shutdown (Low-Power mode)

In shutdown, all power-consuming activities are disabled, though all registers can be written to or read.

This bit cannot be set to 1 when either of the Lock bits is set (bit 6 and bit 7). However, it can be

cleared to 0 for continuous conversion while locked (refer to Section 5.2.1 Shutdown Mode).

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式